iFly 737NG SP 3.2.2

ifly А вот кому нового “китайца”? Главное что он теперь корректно работает с Win 10. Список остальных фич под спойлером, там же линк на скачивание.
SP 3.2.2 Additions and General Improvements:

1. Improvements and optimizations which should result in smoother and more stable fps.
2. Added CDU ACARS RTE Data and DES Forecast Wind requests.
3. Adjustment to the CRT style CDU font.
4. Wind sound now starts at about 60KIAS instead of the previous 10KIAS.
5. The aircraft is now about 2% more “slippery” at altitudes above FL200. The approach must be planned well. However, airspeed increasing 15-20kt over CAB speed is not a problem, so around 300KIAS is OK. Typically, the aircraft slows down nicely to meet SPD or 240/10000 restrictions. Of course speed brakes will be needed at times. Fair Warning: don’t slow the aircraft too aggressively thereby causing IAS to fall behind CAB speed – a large thrust application will result. Stow the spoilers when the IAS is 5-10KTs above the CAB speed, and then use the speed brake again if needed. Not every flight, STAR, and approach is the same, so you will need to relearn and adjust to the aircraft.
6. Improvements to the Autopilot during climb/descent phases in turbulent weather and/or when wind speed and direction change drastically in relation to the aircraft.
7. Adjusted aircraft tendency to aggressively pitch up/down during turns with VNAV/LNAV engaged.
8. Corrected tendency of the aircraft to nose down excessively when using speed brakes.
9. Further improved RTE drawing on the ND. There could be some situations where drawing is not 100% perfect.
10. Updated SDK to v1.10

SP 3.2.2 Fix List:

1. Air file adjusted for better single engine operation.
2. RWY heading angle navdata anomaly
3. VHF Failure
4. RWY ALT issue with Negative values
5. Configuration Tool seating
6. VC static yoke imprint
7. ALT INT
8. RTA improved. Note: if the waypoint is at CLB/DES stage, the speed will not be reliable. RTA is greatly dependent on proper wind entry.
9. FSX/P3D APU BATT charge and Panel switch position settings.
10. IAN barometric path.
11. Turn back after Exec MOD RTE
12. Offsets for WXR
13. T/D & E/D calculation and display
14. CPFlight WXR Panel
15. VOR DME approach with hold
16. MFD C/R Button
17. VECTOR approaches
18. HDG SEL when in VOR/LOC Approach mode

In addition to the above for the CBE:

1. SDK pushback command
2. Export flight plan file when pressing EXEC
3. ROUTE OFFSET
4. Drift down speed on CDU ENG OUT page
5. Navigational beacons missing on Client ND.
6. FO VSD
7. Client Aux Fuel gauge added
8. Resolved Win10 compatibility issues.

Ссылки доступны для скачивания только пользователям с лицензией 🙂

FS2004: http://ifly.flight1.net/forums/forum_posts.asp?TID=14650&title=how-to-install-sp-322

FSX: http://ifly.flight1.net/forums/forum_posts.asp?TID=14651&title=how-to-install-sp-322

P3D: http://ifly.flight1.net/forums/forum_posts.asp?TID=14648&title=how-to-install-sp-322

FSX CBE: http://ifly.flight1.net/forums/forum_posts.asp?TID=14647&title=how-to-install-sp-322

Помощь с покупкой дополнений, подписок и т.д
Чат-болталка в Telegram
 

Поделиться с друзьями

Уже почти 15 лет пишу новости на этом сайте, и как ни странно, разбираюсь в ваших симуляторах.
Летаю на:
AMD Ryzen 7800x3d
/RTX4080 MSI
/64 Gb DDR5 6000
/Win 11 Pro for Workstation

Оцените автора
( Пока оценок нет )
simFlight Russia

Leave a Reply