ATR 42/72-600 – большое обновление

Added marker for MAX throttle position to calibration window
· EFB Options items re-arranged
· Fixed Nav source not switching to NAV2 when V/ILS2 is selected on CPT side
· Fixed MFC test timing
· Fixed CoG graph coordinate calculation
· Added EFB option for display unit clickspot help overlay
· Added clickspot help overlay to MFD and EWD (graphics are placeholders!)
· Changed nose wheel steering to a new method (without fighting control inputs)
· Fixed Flight Idle TQ now drops to 0.0% in flight
· Fixed Gear lever now locked in down position on the ground
· Fixed PROG page total distance and EFOB calculation
· Fixed Power Management knobs animation synchronization
· Fixed GW/FOB indications on EWD not updating when engines running
· Removed automatic wind entry from PERF APPROACH page
· Fixed VApp calculation on PERF APPROACH page (FCOM LIM.3.4.9 p15)
· Fixed roll hold mode
· Added workaround to reduce the prop RPM of engine 2 in hotel mode to around 0
· Fixed enroute holding tracking
· Fixed PFD throttle hint status not loaded from config (Community report)
· Fixed cabin/compartment temperature jumping
· Removed COM3 radio from systems.cfg
· Fixed MAN CAB ALT default position to neutral
· Fixed SOURCE SEL pushbutton to show MAN when released
· Fixed MODE SEL pushbutton to show MAN when released
· Changed SOURCE SEL and MODE SEL pushbuttons to be pressed in on loading
· Added Landing Elevation is now set to destination airport/runway elevation after activating flightplan
· Changed default setting for DH/MDA knobs to MDA
· Removed standby instrument baro from synchronization to allow standard operating procedure of leaving it at local QNH
· Corrected INT/RAD switches to spring-loaded 3-state switches
· Added a separate button for ACW Ground Power on the EFB Aircraft page
· Fixed EFB aircraft state buttons not reacting on mouse over
· Fixed Probes warnings with ACW gens offline, while airborne
· Fixed AMP meter indications
· Fixed bug where AICE FAULTs would not be shown in the MFD MEMO area
· (Re-)activated conditional drawing for certain PFD/MFD display areas
· Fixed bug where ECL procedure version would not differentiate between PROP BRAKE SET or NOT SET
· Fix for MFD VCP PERF PAGE Confirm Takeoff Data button not being updated
· Added animation code for CVR Test and lighting for GND CTL button based on Magnars description
· Fix for PFD MDA colored altitude shown, despite MDA not being active
· Implemented IS_PROCEDURE_DETAIL_SET() method
· Fixed power source for MECH Call Horn which should be connected to DCEssBus
· Fixed EFB pax loading related bug
· Implemented cockpit door state dependant MFD VID image
· Added multiple localvars for third party virtual co-pilot implementations
· Fixed second MCDU sometimes locked on a different page than MENU
· Fixed a bug that would cause a negative distance calculation for a waypoint following a route discontinuity
· Fixed a bug in the EFB weight calculations (note: There are no partial passengers, so weights might deviate a bit)
· Added support for 3 letter airport codes in the United States
· Fixed a bug in DME distance calculation
· Fixed a potential crash in the DME arc drawing function
· Added new loading tips localizations
· Added waypoint 1500ft above airport level if no SID is selected
· Fixed all DTO sub pages showing the first listed waypoint as active
· Fixed approach speed remaining selected ON after FMS reset at end of flight
· Fixed MFD SYS CABIN page not reflecting temperature mode (MAN/AUTO)
· Fixed COM2 radio not reaction to reducing volume to zero (VATSIM)
· Fixed gear extending/retracting without hydraulics (note: sound not in sync yet!)
· Fixed a bug which caused DC Gen 2 to show FAULT if only engine#2 was running
· Fixed engine can not be started after shut down by pulling fire handle (“Repair engine” button added to EFB)