FlyByWire теперь умеет VNAV

[APU] APU can now consume fuel – @tracernz (Mike)
[APU] Added xfeed APU fuel capabilities – @Taz5150 (TazX – [Z+1]#0405)
[ATSU] Fix ATIS Auto Update LSK6L to ATIS page instead of ATC MENU – @BravoMike99 (bruno_pt99)
[BLEED] Allow engine start from crossbleed air – @BlueberryKing (BlueberryKing)
[BLEED] Improve bleed page visuals on the SD – @BlueberryKing (BlueberryKing)
[BLEED] Use more accurate pneumatic valves and sensors – @BlueberryKing (BlueberryKing)
[COND] Add Air Conditioning systems failures – @mjuhe (Miquel Juhe)
[COND] Fixed Temp-Indication on CRZ page showing cockpit temperature for fwd and aft cabin – @cptnuss-ops (Lukas)
[EFB/ATSU] Added NOAA (aviationweather.gov) as a METAR source – @tracernz (Mike)
[EFB/ATSU] Use MSFS METAR data rather than FSX cloud data from FBW API – @tracernz (Mike)
[EFB/FWC] Auto Call Outs selectable – @tracernz (Mike)
[EFB/PAYLOAD] flyPad OS 3.2 – Allow for multi-gate boarding when multiple doors are open – @2hwk (2cas)
[EFB] Added UI message on fuel/payload page when GSX is activated – @frankkopp (Frank Kopp)
[EFB] Added pause at T/D function – @2hwk (2Cas#1022)
[EFB] Fixed Simbridge failing to connect if remote setting is enabled then disabled – @DevonDF (Devon#9451)
[EFB] Fixed the main page and landing calculator to use the selected METAR source – @tracernz (Mike)
[EFB] flyPad OS 3.2 – Cosmetic changes for throttle configuration settings and support for multiple airframes – @2hwk (2cas)
[EIS] Added > character to the font – @KiloEchoVictor (Kevin)
[FDR] Add secondary engine parameters to FDR – @Taz5150 (TazX – [Z+2]#0405)
[FLIGHTMODEL] Fix outer to inner tank transfer valve closure – @donstim (donbikes)
[FMS] Add a default RNP of 0.3 for RNP AR procedure legs – @tracernz (Mike)
[FMS] Add basic support for FA legs – @tracernz (Mike)
[FMS] Implement CHECK SPEED MODE message – @BlueberryKing (BlueberryKing)
[FMS] Implement vertical navigation functions – @BlueberryKing (BlueberryKing)
[FMS] Improve layout of PERF CLB, PERF CRZ and PERF DES pages according to H3 – @BlueberryKing (BlueberryKing)
[FMS] Improved robustness of ILS selection – @tracernz (Mike)
[FMS] Load procedures that reference a runway correctly – @tracernz (Mike)
[FMS] Show ILS ident and frequency on ARRIVAL page – @tracernz (Mike)
[FMS] TO SPEEDS TOO LOW uses FQI fuel quantity after engine start to avoid spurious warnings – @tracernz (Mike)
[FMS] Use station declination when appropriate for fix info and place/bearing radials – @tracernz (Mike)
[FWC] Added “twenty five hundred” and “two thousand” callouts – @tracernz (Mike)
[FWC] WING TANK LO LVL message now considers centre tank mode selector – @tracernz (Mike)
[HYD] Added hydraulic reverser actuators – @Crocket63 (crocket)
[ISIS] Fixed the ISIS alt tape order for negative altitudes – @aweissoertel (Alex)
[MCDU/ND] Corrected altitude formatting with respect to transition altitude and transition level – @tracernz (Mike)
[MCDU] Add basic MCDU MENU functionality – @tracernz (Mike)
[MCDU] Add basic annunciator support – @tracernz (Mike)
[MCDU] Don’t calculate V-speeds when FoB not available – @tracernz (Mike)
[MCDU] Fixed the FMGC annunciator light not illuminating – @tracernz (Mike)
[MCDU] PERF APPR page no longer demands QNH and TEMP when outside 180NM from destination – @robertxing2004 (robeet)
[MCDU] Split subsystem scratchpads – @tracernz (Mike)
[MCDU] The remote MCDU protocol now sends the annunciator light state – @tracernz (Mike)
[MCDU] The remote MCDU protocol now sends the display and integral light brightness – @tracernz (Mike)
[MCDU] The remote MCDU protocol now supports the BRT/DIM keys – @tracernz (Mike)
[MCDU] ZFW/ZFWCG auto-fill uses desired values when boarding in progress – @tracernz (Mike)
[ND] Fix ROSE VOR/LS conditions and ILS course – @tracernz (Mike)
[ND] Mask the map below the TCAS/WXR and FM messages – @tracernz (Mike)
[PAYLOAD] Re-enabled FBW sounds when using GSX Integration
[PFD] Adjusted size of pitch trim messages – @tracernz (Mike)
[PFD] Corrected the NO DH logic in the FMS and PFD – @tracernz (Mike)
[SD] Added a display duration of 3s for STS page – @pluce
[SD] Connect SD BLEED page APU bleed pressure indication to correct ADRs – @BlueberryKing (BlueberryKing)
[SD] Corrected fuel transfer valve amber logic – @tracernz (Mike)
[SD] Corrected position of outer tank fuel quantity values – @robertxing2004 (robeet)
[SD] Corrected thickness and position of lower ECAM fuel page lines – @robertxing2004 (robeet)